#ifndef CONFIG_H
#define CONFIG_H
// ALL EDITS BELOW THIS LINE!

/**************************************************************************************************************************
 * Use a Single Color LED for Status Signaling
 * At Startup the LED will blink twice to signal a sucessfull OTAA Join
 *************************************************************************************************************************/
#define LED_PIN PIN_PA7

/**************************************************************************************************************************
 * Enable WS2812B RGB LED Support for the CO2 Addon Board
 * * First LED shows CO2-Level (green: <1000, yellow: 1000-1800, red: >=1800)
 * * Second LED shows LoRa Status (yellow: Joining, green 1s: Joined, green 100ms: Sending, blue 250ms: Received Downlink) 
 * WS2812B_BRIGHT can be set to the desired brightness value for the LEDs (0=off, 255=brightest)
 * Uncomment the 3 following lines to get the default behaviour
 *************************************************************************************************************************/
// #define WS2812B_PIN PIN_PC1
// #define WS2812B_NUM 2
// #define WS2812B_BRIGHT 32

/**************************************************************************************************************************
 * Enable Sending on Button Press, as well as CO2 Background Level Calibration by Pressing Button for 4s with MH-Z19C Addon
 * The Button has to be connected to a pin that is capable of Fully Asynchronus Interrupts.
 * For The ATTNode this means Pin PC2 if you don't want to block any other Interfaces
 *************************************************************************************************************************/
// #define BTN_PIN PIN_PC2

/**************************************************************************************************************************
 * Number of active Sensors (used as long as HAS_NO_SENSOR is not enabled)
 * Set to the correct number of enabled sensors below
 * Not doing so will lead to unpredictable results or not work at all
 * The default payload decoder will NOT WORK if more than one sensor is enabled, so you MUST define a specific
 * decoder for this case. See the README.md for details
 *************************************************************************************************************************/
#define NUM_SENSORS 1

/**************************************************************************************************************************
 * Define which Sensors are installed
 * Not all sensors can be used at the same time 
 * For example you can only have one sensor using serial UART
 * If HAS_NO_SENSOR is selected all other activated sensor will be ignored
 *************************************************************************************************************************/
#define HAS_NO_SENSOR
// #define HAS_MHZ19C
// #define HAS_SG112A
// #define HAS_SENSAIRS8
// #define HAS_SCD30
// #define HAS_BME280
// #define HAS_SHT21
// #define HAS_HM330x
// #define HAS_DS18B20

/**************************************************************************************************************************
 * Sensor Configuration
 * Change according to your Needs
 *************************************************************************************************************************/
// Pin for the OneWire Bus
#define DS18B20_PIN PIN_PC3
// A/D Resolution of the DS18B20 (9-12 Bit)
#define DS18B20_RES 12

/**************************************************************************************************************************
 * How many minutes to sleep between Measuring/Sending
 * Since this is a 2-byte value internally, intervals between 1 and 65536 are possible
 * This is the default interval to use, which can be overwritten via DownLink. If an interval
 * is set via DownLink it will be saved in EEPROM and the time specified here will no longer be used.
 * Actual sleep Time is sleep_time*2*32 seconds due to the 32s sleep intervals of the ATTiny3216
 *************************************************************************************************************************/
uint16_t sleep_time = 10;

/**************************************************************************************************************************
 * LoRa Keys for OTAA Mode
 * Please make sure to use the correct byte order when copying these from the TTN-Console!
 * APPEUI and DEVEUI need to be inserted in LSB order
 * APPKEY needs to be inserted in MSB order
 * in some cases there is no APPEUI, for example when using Chirpstack. leave it set to all 0x00 in these cases
 *************************************************************************************************************************/
static const u1_t PROGMEM APPEUI[8]  = { 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00 };
static const u1_t PROGMEM DEVEUI[8]  = { 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00 };
static const u1_t PROGMEM APPKEY[16] = { 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00 };

// ALL EDITS ABOVE THIS LINE!
#endif