Add Calibration for SCD30

This commit is contained in:
seiichiro 2021-03-31 19:00:43 +02:00
parent 98893c2894
commit c455a7c7a7
4 changed files with 28 additions and 10 deletions

View file

@ -40,6 +40,9 @@ class AttSensor {
// Return the number of Bytes added to the Payload
virtual uint8_t numBytes(void) = 0;
// Calibrate a Sensor. Needs to be Implemented in the Child Class if supported
void calibrate(void) {};
// Helper Functions to Put Values Into the Payload Array
static void int32ToPayload(int32_t value, char *payload, uint8_t startbyte) {
payload[startbyte] = (value) & 0XFF;

View file

@ -29,8 +29,15 @@
// Constructor - Inititalize Hardware UART
MHZ19C::MHZ19C(void) {
Serial.begin(9600);
Serial.setTimeout(MHZ19C_READ_TIMEOUT);
Serial.begin(9600);
Serial.setTimeout(MHZ19C_READ_TIMEOUT);
}
MHZ19C::MHZ19C(pin_size_t calpin) {
this->calpin = calpin;
Serial.begin(9600);
Serial.setTimeout(MHZ19C_READ_TIMEOUT);
}
void MHZ19C::initialize(void) {
@ -41,6 +48,14 @@ void MHZ19C::initialize(void) {
#endif
}
void MHZ19C::calibrate(void) {
pinMode(calpin, OUTPUT);
digitalWrite(calpin, LOW);
delay(7500);
digitalWrite(calpin, HIGH);
pinMode(PIN_PB4, INPUT_PULLUP);
}
uint8_t MHZ19C::getSensorData(char * payload, uint8_t startbyte) {
write(MHZ19C_CMD_GET_PPM, 0x00);
delay(50);

View file

@ -38,6 +38,7 @@
class MHZ19C : public AttSensor {
private:
uint8_t buffer[MHZ19C_SER_BUF_LEN];
pin_size_t calpin = PIN_PB4; // PB4 is the Calibration Pin on the Addon PCB
void write(byte cmd, byte arg);
uint8_t read();
@ -47,7 +48,9 @@ class MHZ19C : public AttSensor {
public:
MHZ19C(void);
MHZ19C(pin_size_t calpin);
void initialize(void);
void calibrate(void);
uint8_t numBytes(void) {return 2;};
uint8_t getSensorData(char *payload, uint8_t startbyte);
void setSelfCalibration(bool state);

View file

@ -364,17 +364,14 @@ void setup()
void loop()
{
// Handle long Button Press for Calibration with MH-Z19C Sensor
#if defined HAS_MHZ19C && defined BTN_PIN
#ifdef BTN_PIN
if (digitalRead(BTN_PIN) == LOW) {
// Press Button longer than 4 Seconds -> Start MH-Z19C Calibration Routine
// Press Button longer than 4 Seconds -> Start Sensor Calibration Routine (if applicable)
unsigned long loop_millis = millis();
if ((unsigned long)(loop_millis - btn_millis) >= 4000) {
WS2812B_SETLED(1,153,0,153);
pinMode(PIN_PB4, OUTPUT);
digitalWrite(PIN_PB4, LOW);
delay(7500);
digitalWrite(PIN_PB4, HIGH);
pinMode(PIN_PB4, INPUT_PULLUP);
for (uint8_t i=0; i<NUM_SENSORS; i++)
sensors[i]->calibrate();
WS2812B_SETLED(1,0,0,0);
} else {
delay(500);
@ -383,7 +380,7 @@ void loop()
#endif
// Only Run the LMIC loop here. Actual Sending Code is in do_send()
os_runloop_once();
#if defined HAS_MHZ19C && defined BTN_PIN
#ifdef BTN_PIN
}
#endif
}