attnode/v3_firmware
2
0
Fork 0
Code Issues Pull requests Releases Activity

Implement Ad Hoc Sending on Button Press

Browse source 
Added MH-Z19C Calibration
This commit is contained in:
seiichiro 2021-03-14 20:11:03 +01:00
parent cf71223c30
commit 715e2fe22d
2 changed files with 56 additions and 4 deletions
Show stats Download patch file Download diff file Expand all files Collapse all files

5
src/config.h.example
View file

@ -13,6 +13,11 @@
// #define WS2812B_NUM 2
// #define WS2812B_BRIGHT 32
// Enable Sending on Button Press, as well as Calibration by Pressing Button for 4s with MH-Z19C Addon
// The Button has to be connected to a pin that is capable of Fully Asynchronus Interrupts.
// For The ATTNode this means Pin PC2 if you don't want to block any other Interfaces
// #define BTN_PIN PIN_PC2
// Enable Serial Debugging. Parameters for the Serial Port are 115200
// Please be aware that the SG112A/B CO2 Sensor uses the HW-UART, so
// Serial Debug Output is not available with this Sensor.

49
src/main.cpp
View file

@ -94,6 +94,18 @@ const int disabledPins[] = {PIN_PB5, PIN_PB4, PIN_PB1, PIN_PB0, PIN_PC3, PIN_PC2
const int disabledPins[] = {PIN_PB5, PIN_PB4, PIN_PB3, PIN_PB2, PIN_PB1, PIN_PB0, PIN_PC3, PIN_PC2, PIN_PC1, PIN_PC0};
#endif
#ifdef BTN_PIN
volatile bool btn_pressed = 0;
volatile unsigned long btn_millis = 0;
// ISR Routine for Button
void btn_press() {
btn_pressed = 1;
btn_millis = millis();
delayMicroseconds(250000);
}
#endif
// ISR Routine for Sleep
ISR(RTC_PIT_vect)
{
@ -143,8 +155,18 @@ void onEvent(ev_t ev) {
// Got to sleep for specified Time
DEBUG_PRINTLN("Going to Sleep");
for (uint16_t i = 0; i < sleep_time*2; i++)
for (uint16_t i = 0; i < sleep_time*2; i++) {
#ifdef BTN_PIN
if (btn_pressed) {
i = sleep_time*2;
btn_pressed = 0;
} else {
#endif
sleep_32s();
#ifdef BTN_PIN
}
#endif
}
// Schedule Next Transmit
do_send(&sendjob);
@ -231,6 +253,11 @@ void setup()
leds.setBrightness(WS2812B_BRIGHT);
#endif
#ifdef BTN_PIN
pinMode(BTN_PIN, INPUT_PULLUP);
attachInterrupt(digitalPinToInterrupt(BTN_PIN), btn_press, FALLING);
#endif
// Set RTC
while (RTC.STATUS > 0) {}
RTC.CLKSEL = RTC_CLKSEL_INT1K_gc;
@ -272,6 +299,26 @@ void setup()
void loop()
{
#if defined HAS_MHZ19C && defined BTN_PIN
if (digitalRead(BTN_PIN) == LOW) {
// Press Button longer than 4 Seconds -> Start MH-Z19C Calibration Routine
unsigned long loop_millis = millis();
if ((unsigned long)(loop_millis - btn_millis) >= 4000) {
WS2812B_SETLED(1,153,0,153);
pinMode(PIN_PB4, OUTPUT);
digitalWrite(PIN_PB4, LOW);
delay(7500);
digitalWrite(PIN_PB4, HIGH);
pinMode(PIN_PB4, INPUT_PULLUP);
WS2812B_SETLED(1,0,0,0);
} else {
delay(500);
}
} else {
#endif
// Only Run the LMIC loop here. Actual Sending Code is in do_send()
os_runloop_once();
#if defined HAS_MHZ19C && defined BTN_PIN
}
#endif
}