/*
  main.cpp - TinyLora BMP280 Firmware
  Copyright (c) 2019, Stefan Brand
  All rights reserved.

  Redistribution and use in source and binary forms, with or without
  modification, are permitted provided that the following conditions are met:

  1. Redistributions of source code must retain the above copyright notice, this
     list of conditions and the following disclaimer.

  2. Redistributions in binary form must reproduce the above copyright notice,
     this list of conditions and the following disclaimer in the documentation
     and/or other materials provided with the distribution.

  3. Neither the name of the copyright holder nor the names of its
     contributors may be used to endorse or promote products derived from
     this software without specific prior written permission.

  THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
  AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
  IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
  DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
  FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
  DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
  SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
  CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
  OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
  OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*/
#include <Arduino.h>
#include <avr/sleep.h>
#include <avr/wdt.h>
#include <tinySPI.h>

// secconfig.h Configures RF Module, TTN Keys / RF Networks and used Sensor
#include "secconfig.h"

#ifdef RF_LORA
  // Include LoRaWAN
  #include <LoRaWAN.h>
  #define DIO0 PIN_B0
  #define NSS  PIN_B1
  RFM95 rfm(DIO0,NSS);
  LoRaWAN lora = LoRaWAN(rfm);
  uint16_t Frame_Counter_Tx = 0x0000;
#endif

#ifdef RF_RFM69
  // Include RFM69
  #include <RFM69_f.h>
  RFM69 radio;
#endif

// Sensorclass and deepsleep interval (for measurement about every 10Min)
#ifdef HAS_BME280
  #include <BME280.h>
  BME280 sensor;
  #define SLEEP_TIME 528
#endif

#ifdef HAS_SHT21
  #include <SHT21.h>
  SHT21 sensor;
  #define SLEEP_TIME 544
#endif

// Global Variable used for deep sleep
uint16_t sleep_interval;

// Setup Wakeup Interrupt Timer
void init_wdt()
{
  MCUSR &= ~(1<<WDRF);
  // Start timed sequence
  // Set Watchdog Change Enable bit
  WDTCSR |= (1<<WDCE) | (1<<WDE);
  // Set new prescaler (8 sec), unset reset enable
  // enable WDT interrupt
  WDTCSR = (1<<WDIE)|(1<<WDP3)|(1<<WDP0);
}

// Enter Sleepmode, Sleep for s Seconds
void sleep(uint16_t s)
{
  s = s/8;
  sleep_interval = 0;
  while (sleep_interval < s) {
    set_sleep_mode(SLEEP_MODE_PWR_DOWN);
    sleep_mode();
  }
}

// Watchdog Callback for Sleep Timer
ISR(WATCHDOG_vect) {
  sleep_interval++;  // set global flag
  // Start timed sequence
  // Set Watchdog Change Enable bit
  WDTCSR |= (1<<WDCE) | (1<<WDE);
  // Set new prescaler (8 sec), unset reset enable
  // enable WDT interrupt
  WDTCSR = (1<<WDIE)|(1<<WDP3)|(1<<WDP0);
}

// Get Battery Voltage
int32_t readVcc() {
  bitClear(PRR, PRADC);
  ADCSRA |= bit(ADEN); // Enable the ADC
  int32_t result;
  ADMUX = _BV(MUX5) | _BV(MUX0); // For ATtiny84
  delay(2); // Wait for Vref to settle
  ADCSRA |= _BV(ADSC); // Convert
  while (bit_is_set(ADCSRA,ADSC));
  result = ADCL;
  result |= ADCH<<8;
  result = 1126400L / result; // Back-calculate Vcc in mV
  ADCSRA &= ~ bit(ADEN);
  bitSet(PRR, PRADC); // Disable the ADC to save power
  return result;
}

void setup()
{
  // Initialize Sleep Timer
  init_wdt();
  PRR = bit(PRTIM1);

  #ifdef RF_LORA
    // Setup LoraWAN
    rfm.init();
    lora.setKeys(NwkSkey, AppSkey, DevAddr);
  #endif

  #ifdef RF_RFM69
    radio.initialize(RF69_433MHZ,RFM69_NODEID,RFM69_NETWORKID);
    #ifdef RFM69_ENCKEY
      radio.encrypt(RFM69_ENCKEY);
    #endif
    radio.setPowerLevel(RFM69_TXPOWER);
    radio.sleep();
  #endif

  // Setup LED if defined
  #ifdef LED_PIN
    pinMode(LED_PIN, OUTPUT);
  #endif
  delay(50);
}


void loop()
{
  // Buffer to send data
  int32_t data[4];

  // Get Sensor Data
  #ifdef HAS_BME280
    sensor.getData(&data[0], &data[1], &data[2]);
  #endif

  #ifdef HAS_SHT21
    data[0] = (int32_t)(sensor.getTemperature()*100);
    data[1] = 0;
    data[2] = (int32_t)(sensor.getHumidity()*100);
  #endif
  
  data[3] = readVcc();

  // LED On before Sending
  #ifdef LED_PIN
    digitalWrite(LED_PIN, 1);
  #endif
  
  #ifdef RF_LORA
    // Send LoRa Packet, Increment Frame Counter
    lora.Send_Data((unsigned char *)data, sizeof(data), Frame_Counter_Tx);
    Frame_Counter_Tx++;
  #endif

  #ifdef RF_RFM69
    radio.sendWithRetry(RFM69_GATEWAY, data, sizeof(data), 3);
    radio.sleep();
  #endif

  // Led Off after Sending
  #ifdef LED_PIN
    digitalWrite(LED_PIN, 0);
  #endif

  // Sleep until next Measurement
  sleep(SLEEP_TIME);
}