/* 
   secconfig.h - Firmware Configuration
   
   * Supported RF Modules
     #define RF_LORA  - HopeRF RFM95 LoRa Module
     #define RF_RFM69 - HopeRF RFM69(H)(C)W Module
   
   * Supported Sensors
     #define HAS_NO_SENSOR - No Sensor, just send Battery Voltage (Beacon Mode)
     #define HAS_SHT21  - Sensirion SHT21 Temperature + Humidity Sensor
     #define HAS_BME280 - Bosch BME280 Temperature + Humidity + Pressure Sensor
     #define HAS_SHT21_BRIGHTNESS  - SHT21 + Brightness via LED
     #define HAS_BME280_BRIGHTNESS - BME280 + Brightness via LED
     #define HAS_ALARM - send message when pin is triggered

   * LED Support
     #define LED_PIN PIN_A7 - LED is connected to ATTiny84 Pin A7 on TinyTX SMD / TinyLora

   * Brightness Measurement
     LED connected between 2 pins, switched in reverse direction for brightness measurement
     #define LED_K PIN_A7 - LED Cathode
     #define LED_A PIN_B2 - LED Anode

   * Alarm
     #define ALARM_PIN PIN_A0
     if pin changed , change also PCMSK0 = (1<<PCINT0); to corrent PCINT

   * Time between Measurements
     #define SLEEP_TIME 528 - Time in Seconds between Measurements. Try it out to get a good Approximation
     Examples from my Tests::
       - 528 for 10 Minute Interval with a LoRa RFM95 + BME280
       - 544 for 10 Minute Interval with a LoRa RFM95 + SHT21
     
   * See the following Examples for needed RF Module Parameters, uncomment and adapt the one fitting your Hardware
*/


// LoRa RFM95 + SHT21, LED on Pin A7
  #define RF_LORA
  #define HAS_SHT21
  #define LED_PIN PIN_A7
  #define SLEEP_TIME 544
  // Information from The Things Network, device configuration ACTIVATION METHOD: ABP, msb left
  unsigned char NwkSkey[16] = { 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00 };
  unsigned char AppSkey[16] = { 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00 };
  unsigned char DevAddr[4] = { 0x00, 0x00, 0x00, 0x00 };

/* RFM69 + BME280, LED on Pin A7
  #define RF_RFM69
  #define HAS_BME280
  #define LED_PIN PIN_A7
  #define RFM69_NETWORKID 101 // NetworkID, 0-255, sould be the same for Node and Receiver
  #define RFM69_NODEID     29 // NodeID of this Sensor, 1-255, should be unique for every node in the same Network
  #define RFM69_GATEWAY     1 // NodeID of the Receiver, 1-255
  #define RFM69_TXPOWER    31 // Transmitting Power 0-31, see datasheet for details
  #define RFM69_ENCKEY    "0123456789ABCDEF" // AES encryption key, exactly 16 characters, if set messages will be encrypted using AES 128bit
*/

/*
// LoRa RFM95 + BME280 + Brightness Measurement
  #define RF_LORA
  #define HAS_BME280_BRIGHTNESS
  #define LED_K PIN_A7
  #define LED_A PIN_B2
  #define SLEEP_TIME 544
  */

/*
// LoRa RFM95 + Alarm
  #define RF_LORA
  #define HAS_ALARM
  #define ALARM_PIN PIN_A0
  #define LED_PIN PIN_A7
  #define SLEEP_TIME 544 
  */